收藏本站
JTAG-Booster for IDT 64145
1.4.
Trouble Shooting
Avoid long distances between your Host-PC and the target. If you are using
standard parallel extension cable, the JTAG-BOOSTER may not work. Don't
use Dongles between the parallel port and the JTAG-BOOSTER.
Switch off all special modes of your printer port (EPP, ECP, ...) in the BIOS
setup. Only standard parallel port (SPP) mode is allowed.
On very fast PCs there could be verify errors. To avoid this, watch for the
′IO recovery time′-switch in the BIOS Setup which must be turned on.
Otherwise try to slow down your PC by setting the turbo switch off.
When using older flash devices (nearly maximum erase cycles reached), we
propose to use the /VERIFY option. This is also true for the relatively slow 3 Volt
only flash devices.
Some newer fast flash devices need a setup time between address/data and
the write strobe signal. If programming of this devices fails, try with the option
/WRSETUP again.
If there are problems with autodetection of the flash devices use the /DEVICE=
option. To speed up autodetection specify the option /16BIT or /8BIT.
Don't use hardware protected flash memories.
The used chip selects must be defined as output and inactive in the initialization
file (see chapter 1.6 “Initialization file JTAG145.INI”). Also the address bits must
be defined as output.
JTAG145a.doc
9
发布紧急采购，3分钟左右您将得到回复。

采购需求

(若只采购一条型号，填写一行即可)

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

*型号 *数量 厂商 批号 封装
添加更多采购

我的联系方式

*
*
*
相关PDF资料
FS-940 JTAG-BOOSTER FOR ADSP-21XXX 5V
FSICEBASE BASE STATION FSICE FOR MCU MOD
FT24C02A-5LR-T IC EEPROM 2KBIT 1MHZ SOT23-5
FT24C16A-UMR-B IC EEPROM 16KBIT 1MHZ 8MSOP
FT24C256A-UMR-B IC EEPROM 256KBIT 1MHZ 8MSOP
FT24C512A-UDR-B IC EEPROM 512KBIT 1MHZ 8DIP
FT24C64A-UMR-B IC EEPROM 64KBIT 1MHZ 8MSOP
FT822AA IC LED DRVR PFC LOW TDH 8SOP
相关代理商/技术参数
FS-940 功能描述:开发板和工具包 - ARM JTAG Booster PC ADSP-21xxx 5V RoHS:否 制造商:Arduino 产品:Development Boards 工具用于评估:ATSAM3X8EA-AU 核心:ARM Cortex M3 接口类型:DAC, ICSP, JTAG, UART, USB 工作电源电压:3.3 V
FS-945 功能描述:开发板和工具包 - ARM JTAG Booster PC Elan SC400 3.3V RoHS:否 制造商:Arduino 产品:Development Boards 工具用于评估:ATSAM3X8EA-AU 核心:ARM Cortex M3 接口类型:DAC, ICSP, JTAG, UART, USB 工作电源电压:3.3 V
FS94NS 制造商:BOTHHAND 制造商全称:Bothhand USA, LP. 功能描述:SMD, 14 PIN, 10 BASE-T FILTER FOR PCMCIA APPLICATIONS
FS-952 功能描述:EVAL BOARD SUPER 10 ST10R302 RoHS:否 类别:编程器，开发系统 >> 通用嵌入式开发板和套件（MCU、DSP、FPGA、CPLD等） 系列:Digi/FS Forth 标准包装:1 系列:PICDEM™ 类型:MCU 适用于相关产品:PIC10F206，PIC16F690，PIC16F819 所含物品:板，线缆，元件，CD，PICkit 编程器 产品目录页面:659 (CN2011-ZH PDF)
FS-953 功能描述:开发板和工具包 - ARM JTAG Booster PC ADSP-21xxx 3.3V RoHS:否 制造商:Arduino 产品:Development Boards 工具用于评估:ATSAM3X8EA-AU 核心:ARM Cortex M3 接口类型:DAC, ICSP, JTAG, UART, USB 工作电源电压:3.3 V
FS-958 功能描述:开发板和工具包 - ARM JTAG Booster PC Software Upgrade RoHS:否 制造商:Arduino 产品:Development Boards 工具用于评估:ATSAM3X8EA-AU 核心:ARM Cortex M3 接口类型:DAC, ICSP, JTAG, UART, USB 工作电源电压:3.3 V
FS-969 功能描述:开发板和工具包 - ARM Forth DIMM-520 Dev. Kit f/ Windows CE RoHS:否 制造商:Arduino 产品:Development Boards 工具用于评估:ATSAM3X8EA-AU 核心:ARM Cortex M3 接口类型:DAC, ICSP, JTAG, UART, USB 工作电源电压:3.3 V
FS-970 功能描述:开发板和工具包 - ARM Forth ModNET50 Sup. NET+OS RoHS:否 制造商:Arduino 产品:Development Boards 工具用于评估:ATSAM3X8EA-AU 核心:ARM Cortex M3 接口类型:DAC, ICSP, JTAG, UART, USB 工作电源电压:3.3 V